Question:
2009 Toyota Corolla all key lost and original keys remote keyhead, have added one key using Xhorse Super Remote Ford Style. Is it possible to clone the added one by Key Tool Max Pro and Dolphin XP-005?
Here is the Answer:
Yes, clone chip by Key Tool Max Pro, program remote manually, and prepare the blade using Dolphin XP005.
How to Program Remote Manually?
Toyota Corolla 2009 (Smart System)
1.Locate an automotive locksmith in your area using the phone number or find on the internet.
2.If your vehicle is still mobile, it may save you money by driving to the locksmith instead of having them come to you.
3.The locksmith will then hook up specialized computer equipment to your vehicle in order to program the smart key remote fob.
If your Corolla has a remote head key you can use the following instructions to program the remote portion of the remote key but you will need to have a Locksmith program the key portion.
IF TEN SECONDS OR MORE ELAPSE BETWEEN ANY OF THE FOLLOWING STEPS,YOU WILL NEED TO START ALL OVER AGAIN.PREPARE VEHICLE BY CLOSING AND LOCKING ALL DOORS EXCEPT DRIVER’S DOOR SHOULD BE OPEN AND UNLOCKED.
1)STICK KEY IN AND OUT OF THE IGNITION CYLINDER TWICE WITHOUT TURNING IT.
2)CLOSE AND OPEN DRIVER’S DOOR TWICE ENDING IN OPEN DOOR.
3)STICK KEY IN AND OUT OF THE IGNITION CYLINDER ONCE WITHOUT TURNING IT.
4)CLOSE AND OPEN DRIVER’S DOOR TWICE ENDING IN OPEN DOOR.
5)STICK THE KEY IN THE IGNITION CYLINDER.(DO NOT REMOVE OR TURN KEY)
6)CLOSE DRIVER’S DOOR.
7)TURN THE KEY IN THE IGNITION ON AND OFF TWICE AND REMOVE KEY FROM THE IGNITION.
(AT THIS POINT IF EVERY STEP WAS DONE CORRECTLY,ALL DOORS WILL LOCK AND UNLOCK TWICE TO LET YOU KNOW THE SYSTEM ENTERED THE ADD MODE)
8)PRESS BOTH LOCK AND UNLOCK BUTTONS ON YOUR REMOTE SIMULTANEOUSLY FOR ONE SECOND.
9)WITHIN THREE SECONDS PRESS THE LOCK BUTTON ON YOUR REMOTE FOR ONE SECOND AND RELEASE.
(VEHICLE WILL BEEP TWICE TO LET YOU KNOW IT HAS ACCEPTED THE NEW REMOTE.)
TO EXIT ADD MODE OPEN AND CLOSE DOOR AND TEST REMOTE OPERATION.
Toyota Corolla 2001 – 2014 (CANADA TMC)
*Make sure the driver’s door is open and unlocked and Key is out of the ignition.
1.INSERT and REMOVE the key from the ignition key cylinder twice within 5 seconds.
2.CLOSE and OPEN the driver’s door twice within 40 seconds.
3.INSERT the key into the ignition and remove it, do not turn.
4.CLOSE and OPEN the driver’s door twice within 40 seconds.
5.INSERT the key into the ignition.
6.CLOSE the door.
7.Turn the ignition switch from LOCK to ON and back to LOCK at about 1 second intervals
to select the desired mode :
NOTE: 1 time for ADD.
NOTE: 2 times for REWRITE.
NOTE: 3 times for CONFIRMATION.
NOTE: 5 times for PROHIBITION.
8.Remove the key from the ignition.
NOTE : To confirm your selection of all modes except CONFIRMATION, the power locks
will now cycle LOCK to UNLOCK a number of times corresponding the mode selected.
NOTE : If CONFIRMATION mode has been selected, the power door locks will now cycle
in 2 seconds intervals) a number of times corresponding to the number of transmitters currently registered.
Opening the door will complete the procedure.
NOTE : If PROHIBITION mode has been selected, opening the door will complete the procedure.
- For ADD or REWRITE modes, within 20 seconds of Door Lock confirmation proceed as follows :
(a) Press both transmitter LOCK and UNLOCK buttons simultaneously between 1 and 1.5 seconds and release.
(b) Within 3 seconds of step (a), press the transmitter LOCK button for more than 1 second and release.
(c) If the transmitter has been successfully programmed, the power locks will cycle LOCK to UNLOCK
once at this time. If there are problems with the procedure up to this point, the locks
will cycle twice, in which case you must go back and repeat the above steps (a) and (b).
(d) If multiple transmitters are to be programmed, repeat the above steps (a) to (c).
- Open the driver’s door to complete the procedure.
Hope this could help!
CRE: Ключар Бургас
https://www.xhorsevvdi.com/
Skype: xhorsevvdi.com
Whatsapp:+86-13983756354
Whatsapp: 
Skype: